Apeks O-ring chart

Discussion in 'Repairing your own Gear' started by steveharriss, Jun 16, 2013.

  1. steveharriss

    steveharriss Nassau Grouper

    109
    38
    0
    [TABLE="class: outer_border, width: 800"]
    [TR]
    [TD] [TABLE]
    [TR]
    [TD]Apeks ID[/TD]
    [TD]BS (in brackets for Metric)[/TD]
    [TD]Cross Section[/TD]
    [TD]Inner diam.[/TD]
    [TD]SCUBA Application Seal[/TD]
    [TD][/TD]
    [/TR]
    [TR]
    [TD]AP1157[/TD]
    [TD]003[/TD]
    [TD]1/16[/TD]
    [TD]1/16[/TD]
    [TD]High-Pressure Hose/SPG swivel[/TD]
    [TD][/TD]
    [/TR]
    [TR]
    [TD]AP6403[/TD]
    [TD]004[/TD]
    [TD]1/16[/TD]
    [TD]5/64[/TD]
    [TD]High-Pressure Hose/SPG swivel (less common)[/TD]
    [TD]2mm x 1.78mm[/TD]
    [/TR]
    [TR]
    [TD]AP1299[/TD]
    [TD]006[/TD]
    [TD]1/16[/TD]
    [TD]1/8[/TD]
    [TD]Apeks HP seat (1st stage)[/TD]
    [TD]3mm x 1.78mm[/TD]
    [/TR]
    [TR]
    [TD]AP1564[/TD]
    [TD]006[/TD]
    [TD]2.9mm[/TD]
    [TD]1.78mm[/TD]
    [TD]Power Inflator spindle (Polyurethane)[/TD]
    [TD]70 Shore[/TD]
    [/TR]
    [TR]
    [TD]AP1282[/TD]
    [TD]007[/TD]
    [TD][/TD]
    [TD][/TD]
    [TD][/TD]
    [TD]4mm x 1.78mm[/TD]
    [/TR]
    [TR]
    [TD]AP1154[/TD]
    [TD]010[/TD]
    [TD]1/16[/TD]
    [TD]1/4[/TD]
    [TD]Low-Pressure Hose/2nd Stage Regulator
    Cylinder Valve Stem
    Apeks crown (2nd stage)[/TD]
    [TD]6mm x 1.78mm[/TD]
    [/TR]
    [TR]
    [TD]AP1409[/TD]
    [TD]011[/TD]
    [TD]1/16[/TD]
    [TD]5/16[/TD]
    [TD]Standard Low-Pressure Port/Hose (3/8 UNF)
    Apeks adjusting screw (2nd stage)
    Apeks conical filter (1st Stage)
    Apeks FSR HP crown (1st stage)
    Power Inflator quick disconnect oring[/TD]
    [TD]7.6mm x 1.78mm[/TD]
    [/TR]
    [TR]
    [TD]AP1445[/TD]
    [TD]012[/TD]
    [TD]1/16[/TD]
    [TD]3/8[/TD]
    [TD]High-Pressure Port/Hose (7/16 UNF)
    Manifold and Manifold Port Plugs[/TD]
    [TD]9.5mm x 1.78mm[/TD]
    [/TR]
    [TR]
    [TD][/TD]
    [TD]012[/TD]
    [TD]1/16[/TD]
    [TD]3/8[/TD]
    [TD]Power Inflator cylinder inner oring (Buna)[/TD]
    [TD][/TD]
    [/TR]
    [TR]
    [TD]AP1410[/TD]
    [TD]013[/TD]
    [TD]1/16[/TD]
    [TD]7/16[/TD]
    [TD]Large Low-Pressure Port/Hose (1/2 UNF)
    Apeks balance plug inner (1st stage)[/TD]
    [TD]11mm x 1.78mm[/TD]
    [/TR]
    [TR]
    [TD]AP1159[/TD]
    [TD]014[/TD]
    [TD]1/16[/TD]
    [TD]1/2[/TD]
    [TD]Standard Yoke Regulator/K-valve
    Apeks ATX adjuster screw (2nd stage)[/TD]
    [TD]12.5mm x 1.78mm[/TD]
    [/TR]
    [TR]
    [TD]AP1267[/TD]
    [TD]015[/TD]
    [TD]1/16[/TD]
    [TD]9/16[/TD]
    [TD]Apeks value spindle (2nd stage)
    Cylinder Valve Bonnet Nut[/TD]
    [TD]14mm x 1.78mm[/TD]
    [/TR]
    [TR]
    [TD]AP1298[/TD]
    [TD]017[/TD]
    [TD][/TD]
    [TD][/TD]
    [TD][/TD]
    [TD]17.4mm 1.78mm[/TD]
    [/TR]
    [TR]
    [TD]AP4089[/TD]
    [TD]018[/TD]
    [TD][/TD]
    [TD][/TD]
    [TD][/TD]
    [TD]19mm x 1.78mm[/TD]
    [/TR]
    [TR]
    [TD]AP1438[/TD]
    [TD]019[/TD]
    [TD]1/16[/TD]
    [TD]13/16[/TD]
    [TD]Apeks Venturi (2nd stage)
    Apeks turret bolt (1st stage)[/TD]
    [TD]20.5mm x 1.78mm[/TD]
    [/TR]
    [TR]
    [TD]AP1420[/TD]
    [TD]024[/TD]
    [TD][/TD]
    [TD][/TD]
    [TD][/TD]
    [TD]28mm x 1.78mm[/TD]
    [/TR]
    [TR]
    [TD]AP1420[/TD]
    [TD]024[/TD]
    [TD]1/16[/TD]
    [TD]1-1/8[/TD]
    [TD]Apeks Turret (1st stage)[/TD]
    [TD][/TD]
    [/TR]
    [TR]
    [TD]AP1166[/TD]
    [TD]111[/TD]
    [TD]3/32[/TD]
    [TD]7/16[/TD]
    [TD]Apeks DIN Regulator/Valve
    Apeks Yoke spare (2nd stage)
    Note:Yoke valves often use BS112 or BS014[/TD]
    [TD]11mm x 2.62mm[/TD]
    [/TR]
    [TR]
    [TD][/TD]
    [TD]112[/TD]
    [TD]3/32[/TD]
    [TD]1/2[/TD]
    [TD]Power Inflator cylinder outer oring (Buna)[/TD]
    [TD][/TD]
    [/TR]
    [TR]
    [TD]AP1405[/TD]
    [TD]113[/TD]
    [TD][/TD]
    [TD][/TD]
    [TD][/TD]
    [TD]14mm x 2.62mm[/TD]
    [/TR]
    [TR]
    [TD]AP1505[/TD]
    [TD]114[/TD]
    [TD][/TD]
    [TD][/TD]
    [TD][/TD]
    [TD]15.5mm x 2.62mm[/TD]
    [/TR]
    [TR]
    [TD]AP1628[/TD]
    [TD]115[/TD]
    [TD][/TD]
    [TD][/TD]
    [TD][/TD]
    [TD]17.4mm x 2.62mm[/TD]
    [/TR]
    [TR]
    [TD]AP1456[/TD]
    [TD]117[/TD]
    [TD][/TD]
    [TD][/TD]
    [TD][/TD]
    [TD]20.5mm x 2.62mm[/TD]
    [/TR]
    [TR]
    [TD]AP1418[/TD]
    [TD]118[/TD]
    [TD][/TD]
    [TD][/TD]
    [TD][/TD]
    [TD]22mm x 2.62mm[/TD]
    [/TR]
    [TR]
    [TD]AP1277[/TD]
    [TD]119[/TD]
    [TD][/TD]
    [TD][/TD]
    [TD][/TD]
    [TD]23.5mm x 2.62mm[/TD]
    [/TR]
    [TR]
    [TD]AP7502[/TD]
    [TD]610[/TD]
    [TD][/TD]
    [TD][/TD]
    [TD][/TD]
    [TD]70 Shore[/TD]
    [/TR]
    [TR]
    [TD]AP1300[/TD]
    [TD]15x1.5 (0151-16)[/TD]
    [TD]1.5mm[/TD]
    [TD]15mm[/TD]
    [TD]Apeks HP balance plug outer (1st stage)[/TD]
    [TD]BS 15.1mm x 1.6mm[/TD]
    [/TR]
    [TR]
    [TD]AP5711[/TD]
    [TD]2.5x1 (607)[/TD]
    [TD]1mm[/TD]
    [TD]2.5mm[/TD]
    [TD]Apeks ATX adjuster screw nib (2nd stage)[/TD]
    [TD]BS 2.8mm x 1.02mm[/TD]
    [/TR]
    [TR]
    [TD][/TD]
    [TD]204[/TD]
    [TD]1/8[/TD]
    [TD]3/8[/TD]
    [TD]Power Inflator oral inflate oring (Buna)[/TD]
    [TD][/TD]
    [/TR]
    [TR]
    [TD]AP1278[/TD]
    [TD]213/214?[/TD]
    [TD][/TD]
    [TD][/TD]
    [TD][/TD]
    [TD]23.5mm x 3.53mm[/TD]
    [/TR]
    [TR]
    [TD][/TD]
    [TD]214[/TD]
    [TD]1/8[/TD]
    [TD]1[/TD]
    [TD]Cylinder with Large Neck/Valve
    (3/4 NPS - All Aluminum, most Steel cylinders)[/TD]
    [TD][/TD]
    [/TR]
    [TR]
    [TD]AP2041[/TD]
    [TD]2x1 (606)[/TD]
    [TD]1mm[/TD]
    [TD]2mm[/TD]
    [TD]Apeks shuttle valve (2nd stage)[/TD]
    [TD]BS 2mm x 1.02mm[/TD]
    [/TR]
    [/TABLE]
    [/TD]
    [/TR]
    [/TABLE]
     

    Attached Files:

    Last edited: Jun 16, 2013
    kob159014, Zung, Pao and 1 other person like this.

Share This Page