Sherwood dry bleed contaminated piston

Please register or login

Welcome to ScubaBoard, the world's largest scuba diving community. Registration is not required to read the forums, but we encourage you to join. Joining has its benefits and enables you to participate in the discussions.

Benefits of registering include

  • Ability to post and comment on topics and discussions.
  • A Free photo gallery to share your dive photos with the world.
  • You can make this box go away

Joining is quick and easy. Log in or Register now!

Well, damn! Good for you.
But I'm not so sure those [2,500# pressure cleaner] are readily available to most divers. At least I don't have one.
Well, I live in South Florida, and they are very popular here, due the mold that grows here in the roof and driveways from the high humidity. They sell them cheap in Home Depot or Harbor Freight tools. Or you can keep and eye, when you see someone using one, and let them use it for a minute or two. I have been trying for over 10 years for a way to clean them. I am an engineer, so, for me it was a bucket list challenge. :)
 
Folks...

First and foremost...I don't advocate this procedure...only reporting that it works like magic...

On the work-bench of the LDS where I had a post-retirement position for seven years...we had a closed-lid plastic tupperware container with about two inches of what the owner referred to as ''magic water''...

We serviced a lot of old Sherwood/Aqua-lung/Dacor...and a few other...regulators for which replacement sintered filters were no longer available...including the Sherwood ''old style'' pistons with the by-pass filter...

Using a pair of tweezers to hold the part...and for only a few seconds...the part was dipped in the ''magic water''...immediately any contamination fizzed up...contamination being salt/cylinder scale/AL cylinder oxidization dust etc...

The fizzing would only last a couple of seconds...and then stop...when it stopped...the part was immediately removed and rinsed with fresh water...

The parts came out shining like a new penny...and functioned perfectly...with all the contamination plugging the filter gone......

''Magic Water''...first word starts with an ''M''...second word starts with an ''A''...

W...
 
"Magic Water"....interesting.

Think it would deal with silicone grease contamination? One of my mistakes the first time I overhauled a Sherwood was to put the piston in a small basket into the ultrasonic with the rest of the metal parts. Standard 1/2 strength vinegar solution. Piston was already WELL contaminated with salt. Ambient chamber was caked with it. I think the bleed had likely been plugged for awhile so the chamber got flooded when diving.

Didn't know that was not proper procedure. OTOH, I think the initial problem might have been from a shop overhaul and that tech maybe didn't know either. The reg was retired/replaced when it didn't deliver sufficient air in a deep current situation. Sat in a box for years until I started doing my own regs and I thought to check that one out. Amazingly easy to work on compared to many other regs. That was when I found the ambient chamber full of salt crystals, lots of salt crystals.
 
"Magic Water"....interesting.

Think it would deal with silicone grease contamination? One of my mistakes the first time I overhauled a Sherwood was to put the piston in a small basket into the ultrasonic with the rest of the metal parts. Standard 1/2 strength vinegar solution. Piston was already WELL contaminated with salt. Ambient chamber was caked with it. I think the bleed had likely been plugged for awhile so the chamber got flooded when diving.

Didn't know that was not proper procedure. OTOH, I think the initial problem might have been from a shop overhaul and that tech maybe didn't know either. The reg was retired/replaced when it didn't deliver sufficient air in a deep current situation. Sat in a box for years until I started doing my own regs and I thought to check that one out. Amazingly easy to work on compared to many other regs. That was when I found the ambient chamber full of salt crystals, lots of salt crystals.

FM...

If the little piston by-pass filter is plugged...it's likely crystalized salt...and not silicone...silicone grease and/oygen compatible lubricant...unless it's contaminated should pass through the filter...

Our shop regs were Sherwood...I serviced them annually...using OCL...never had any issues...

Some of the older Sherwood pistons are still available...the model with the crimped-in HP seat is not...unless you can find some ''new/old'' stock...

Try the magic water... if the sintered filter starts to fizz...you know right away it's plugged with contaminates

Best...

Warren
 
I don’t think Magic Water dissolves silicone or Christo lube at all.

M...

You may be right...but I don't think ''lube'' unless it's contaminated with particulate matter would be the cause...the plugging has likely occurred gradually...most likely salt/cylinder scale/sand...

Best...

W...
 
If it’s just salt, water should dissolve it.


If it’s calcium or magnesium or potassium deposits, a weak acid should get it done. Have you tried white vinegar?
 
Folks...

First and foremost...I don't advocate this procedure...only reporting that it works like magic...

On the work-bench of the LDS where I had a post-retirement position for seven years...we had a closed-lid plastic tupperware container with about two inches of what the owner referred to as ''magic water''...

We serviced a lot of old Sherwood/Aqua-lung/Dacor...and a few other...regulators for which replacement sintered filters were no longer available...including the Sherwood ''old style'' pistons with the by-pass filter...

Using a pair of tweezers to hold the part...and for only a few seconds...the part was dipped in the ''magic water''...immediately any contamination fizzed up...contamination being salt/cylinder scale/AL cylinder oxidization dust etc...

The fizzing would only last a couple of seconds...and then stop...when it stopped...the part was immediately removed and rinsed with fresh water...

The parts came out shining like a new penny...and functioned perfectly...with all the contamination plugging the filter gone......

''Magic Water''...first word starts with an ''M''...second word starts with an ''A''...

W...


Muratic Acid?
 
After I realized the problem (no bleed bubbles), I tried cleaning with warm filtered pure water in an ultrasonic. Nope. Tried boiling it in same a bit. Boiled longer. Nope
Then same with a tad of simple green. Nope.
Isopropyl alcohol. Nope.
Got pissed and soaked it in methyl ethyl ketone, by gawd. :rant: Nope.
Took a Dremel and a small carborundum bit and tried to make it thinner. For a porous metal that thing is sure tough. :mad: Made a tad of progress, and got a few bubbles for my effort, but not even close to spec. :(

Gave up, got another used one from a generous soul on SB here. Works fine.
 
https://www.shearwater.com/products/peregrine/

Back
Top Bottom