Max Helium fraction continuous blend

Please register or login

Welcome to ScubaBoard, the world's largest scuba diving community. Registration is not required to read the forums, but we encourage you to join. Joining has its benefits and enables you to participate in the discussions.

Benefits of registering include

  • Ability to post and comment on topics and discussions.
  • A Free photo gallery to share your dive photos with the world.
  • You can make this box go away

Joining is quick and easy. Log in or Register now!

I gave up on the little hargraves sampling pump pretty quick. It works to route your trimix inlet gas to a helium analyzer (since they rarely have a remote sensor like an O2 cell). but its just not necessary to CB trimix at all when you can pump raw helium and top of with 32%
That sound like the explanation for DIR Standard Gasses, which are all mixes that can be made by adding 32% to Helium.

Michael
 
That sound like the explanation for DIR Standard Gasses, which are all mixes that can be made by adding 32% to Helium.

Michael
I just pump 100% helium then pull out my wine cork/garbage bag from the stick inlet and switch to 32% to top off. It pushes all the helium through and into my tanks. Dont need to CB trimix at high pressures that way
 
Rjack has the ticket. I wanted to pump raw helium 1st because it simplifies mixing a lot. With the extreme cost and availability issues with He doing it this way you can easily identify exactly where the gas is being used or wasted.

while I haven’t tried CB’ing tri-mix with all the gases flowing through the stick at the same time, I highly suspect that it can’t possibly be as accurate as isolating one of the gasses individually first.

Additionally since I’m only dealing with pure He on the first phase of fill my need for a He analyzer is debatably minimal. If I nail my target temps and pressure on the He fill it’s just basic math and an O2 analyzer for the last phase of fill. For the time being I’m using an He analyzer in addition to an O2 sniffer to ensure my process is viable.

I’ll post up compressor specs later but the monitoring was exactly what you’d expect. Laser thermometer on the key component surfaces and visually examining the oil sight gauge “bulls eye.”

I’ve got several samples drawn however I’ll have to wait until Tuesday to send them out. I’m sending out a samp of: raw unpumped fresh out of the K He, raw He pumped out of the compressor, a final sample of the finished 21/35, and an air samp off the compressor.

I’m tempted to send off a lean nitrox sample too but that’s probably overkill. I might do that if this report indicates my O2 CB’ing muttled my 21/35’s numbers.

I was tempted to “stir” the tanks but they were all doubles and my back can only handle so much fun. It was easier to just park em over night.

I only started this experiment because the timing was right. I got the He on trade, I was planning on overhauling the compressors top end this winter anyways, and I got a few deeper dives I’ve been wanting to do but didn’t want to foot the gas bill.
 
Why are you sending helium off for analysis?

If you recycle leftovers you really need a helium analyzer.
 
I couldn’t get a lab report on it from the manufacturer and I wanted to see how clean the He was before it went through the compressor.
 
I just had my capitano revalved and ringed snf 3rd stage replaced. I used lawrence factor supplied parts. I found out too late that those parts were not Bauer parts but similar parts. when the rebuild was done the shop said I had a high blow by. 1.5 cu ft per minute @ 3000 psi as opposed to about point 7 which was normal. when it went in for rebuild it probably had a 5 cu ft per min blow by. that would make pumping He real expensive.
 
Blowby leaks into the crankcase, and the crankcase is ventilated into the 1st stage intake.

Blowby reduces efficiency, but no gas is lost since it gets sucked back into the 1st stage on oil lubed compressors.

Michael
 
I couldn’t get a lab report on it from the manufacturer and I wanted to see how clean the He was before it went through the compressor.
even 99.99% helium is cleaner than ambient air in san diego lol
 
The blow by contributing to waste is bunk. As it’s been stated it’ll just recirc back to the 1st stage. Additionally you’re not going to pump He at high pressures most of the time. At lower pressures blow by is far less.

SD air quality is bad, hopefully bad enough to hide any contaminates my compressor address :wink:
 
https://www.shearwater.com/products/teric/

Back
Top Bottom