OceanLog software -- can you add pressure at each data point?

[RaginCajun]

I was looking at a few recent dive logs and cannot seem to get the old or even newly updated Ocean Log 2.1.4 software to show me pressure at each dive interval.

I'd really like to know what my pressure was at each time it takes and stores a data point.

Can this be done? Can the software be configured to do this?

I know it can be done with the Uwatec software, because my LDS showed me.

How about Oceanic?

Cheers!

 

[D_B]

Does your computer read tank pressure? Unless it's reading your tank, it's just going to be an average of the entire dive divided by the time elapsed at that point ... probably not a useful figure

 

[sharpenu]

I have the same problem. My VT Pro saves beginning pressure, and it shows ending pressure, but nothing else. Here is an example of the information:

Life Time Dive No.: 6
PDC Model:VT PRO
PDC Serial:3669
PDC Dive No.:3
Dive Date: 07/26/2007
Dive Time: 13:01
Dive Mode: Normal
Surface Interval: 00:51
Max. Depth: 59 FT
Elapsed Dive Time: 59 Minutes
Min Temp: 85 F

Start Pressure: 3540 PSI
End Pressure: 768 PSI
Cylinder Size: 0 FT³
Working Pressure: 0 PSI
SAC: 0 FT³/Min
FO2: 36%
N1: 56.12
N2: 112.13
N3: 107.11
N4: 5.08
N5: 41.07
N6: 83.06
N7: 227.05
N8: 8.05
N9: 50.04
N10: 30.04
OTUD: 81.
OTUS: 30.
Dive Sampling Rate: 30 Secs
Dive Data Type: PDC

Elapsed Dive Time(hh:mm),Depth,Nitrogen Bar Graph,Oxygen Bar Graph,Ascent Rate,Air Time Remaining,Dive Time Remaining,Deco Time,Stop Depth,Temperature,PO2,Tank,Pressure Reading,Link Status,Dive Status
00:00:15,8. FT,2,1,0-10 FPM,N/A,02:07,0:00,0 FT,98,0.45,N/A,N/A,N/A,
00:00:30,17. FT,2,1,0-10 FPM,N/A,01:41,0:00,0 FT,98,0.55,N/A,N/A,N/A,
00:00:45,26. FT,2,1,0-10 FPM,N/A,01:26,0:00,0 FT,98,0.64,N/A,N/A,N/A,
00:01:00,38. FT,2,1,0-10 FPM,N/A,01:11,0:00,0 FT,97,0.77,N/A,N/A,N/A,
00:01:00,44. FT,2,1,11-15 FPM,N/A,00:25,0:00,0 FT,96,0.84,N/A,N/A,N/A,
00:01:15,43. FT,2,1,11-15 FPM,N/A,00:28,0:00,0 FT,95,0.83,N/A,N/A,N/A,


Why do I get "N/A" for all of the tank pressure readings?

 

[RaginCajun]

sharpenu shows it perfectly....no pressure at each data point. Hmmm what's up with this?

I'll try to get some input from one of the Oceanic folks and I'll be sure to reply with what I find out.

 

[RaginCajun]

Update:

Doug Krause from Oceanic sent me a note on the subject.

Problem solved...just buy one of the new units they have the extra bells & whistles.


Hi Todd - I've literally been in meetings all day today. I just saw your post prior to getting this PM. Only the latest generation computers (ATOM 2.0, VT3 and DataMask) capture cylinder pressure at every sampling point.