**SOLD**
Selling my Ikelite 4401.1 Fiber Optic Converter for DS Strobes. Only used for a week of diving, so it's in fantastic condition, barely used.
Ikelite's spiel below:
Converts the electrical bulkhead of any Ikelite DS strobe into a fiber optic port. The Fiber Optic Converter features heightened sensitivity for use with SEA&SEA or Nauticam housings with internal electrical-to-optical flash triggering devices. These devices translate the camera’s electrical signals into a series of LED flashes which are much less bright than a traditional built-in camera flash. The Fiber Optic Converter is also compatible with any system where the camera’s built-in flash can be seen by a fiber optic cord.
The Fiber Optic Converter automatically configures itself for compatibility with both pre-flash and non pre-flash camera modes. No setting of small switches or confusion over number of pre-flashes. Simply turn on your strobe and take one picture to configure. This adapter is a manual exposure (non-TTL) trigger only. The strobe’s output may be adjusted using the manual power settings built into the strobe (varies by model).
An individual Fiber Optic Converter and compatible cord is needed for each strobe. Use of two strobes requires two Fiber Optic Converters. The Fiber Optic Converter supports DS50, DS51, DS125, DS160 and DS161 strobes. Accepts Ikelite, SEA&SEA, and Olympus type fiber optic cords.
For remote slave triggering off another flash without a cable, consider the Optical Slave Converter.
This converter attaches to an Ikelite DS strobe. It is not intended to be attached to a housing and will provide no functionality if attached to an Ikelite bulkhead in a housing.
Fiber Optic Cord Compatibility:
Selling for $120 AUD / $82 USD + shipping
Located in Melbourne, Australia, but happy to ship worldwide.
Selling my Ikelite 4401.1 Fiber Optic Converter for DS Strobes. Only used for a week of diving, so it's in fantastic condition, barely used.
Ikelite's spiel below:
Converts the electrical bulkhead of any Ikelite DS strobe into a fiber optic port. The Fiber Optic Converter features heightened sensitivity for use with SEA&SEA or Nauticam housings with internal electrical-to-optical flash triggering devices. These devices translate the camera’s electrical signals into a series of LED flashes which are much less bright than a traditional built-in camera flash. The Fiber Optic Converter is also compatible with any system where the camera’s built-in flash can be seen by a fiber optic cord.
The Fiber Optic Converter automatically configures itself for compatibility with both pre-flash and non pre-flash camera modes. No setting of small switches or confusion over number of pre-flashes. Simply turn on your strobe and take one picture to configure. This adapter is a manual exposure (non-TTL) trigger only. The strobe’s output may be adjusted using the manual power settings built into the strobe (varies by model).
An individual Fiber Optic Converter and compatible cord is needed for each strobe. Use of two strobes requires two Fiber Optic Converters. The Fiber Optic Converter supports DS50, DS51, DS125, DS160 and DS161 strobes. Accepts Ikelite, SEA&SEA, and Olympus type fiber optic cords.
For remote slave triggering off another flash without a cable, consider the Optical Slave Converter.
This converter attaches to an Ikelite DS strobe. It is not intended to be attached to a housing and will provide no functionality if attached to an Ikelite bulkhead in a housing.
Fiber Optic Cord Compatibility:
- Ikelite Fiber Optic Coiled Cord # 4501
- INON Optical D Cable “Non-wireless type” L-Connector
- SEA&SEA Fiber Optic Cable (L-type) # 50107
- SEA&SEA Fiber Optic Cable II # 50128
- Olympus UW Fiber Optic Cable PTCB-E02
- Nauticam Optical Fiber Cable # 26211 Nauticam to INON
- Nauticam Optical Fiber Cable # 26212 Nauticam to Sea&Sea
Selling for $120 AUD / $82 USD + shipping
Located in Melbourne, Australia, but happy to ship worldwide.
