Peter_C
Contributor
Please take these comments as constructive. With a new product from a company that is new to product design and manufacturing, we hope to see improvements in future versions/releases.
In another post there was a complaint about not being able to push the buttons with thick 5mm gloves on. Many of us dive cold water, and a cold hand/finger may find pushing the buttons very hard, especially with no feeling in said finger.
I find the short USB cable to be a pain, especially since I use a laptop often in my lap. It would be hanging from the front of my desktop if plugged in there to charge. I understand you will probably be offering it with the longer cable to help control the squelch when plugged into a computer. Someone mentioned it is the same connector as some Blackberry's?
We have heard there is a new case being manufactured. I would be curious to see one since I still haven't figured out how I am going to carry it long term. For now it will probably be clipped off into my left pocket, utilizing cave line and a bolt snap tied to the lid. What about offering different options for diver attachment points? Personally I do not think I would trust the metal clip currently on it to keep it attached to my scuba kit being drug into and around my boat (Probably going to remove the metal clip currently installed for cleanliness in my pocket, since it is a suicide type clip). Nor do I want it dangling by clipping the radio off to my BC anywhere. Since I dive a BP/W with a can light, my preference would be to store it directly behind my can light on the 2" waist harness, held in place by the can light which is held in place by a buckle. In other words what about offering possibly a bolt on, or cast in solid mount 2" slot?
Seems like somewhere on this page Nautilus Lifeline Support Registration there should be a link to get the MMSI number from BoatUS with the "how to" write up from another thread found in this forum. Following the instructions was pretty straight up for getting the MMSI number.
The interface software is not laid out properly as you can see in the photo below it is impossible to see what channels are set. Every page has areas where words are cut off too. I set the channels with no issue and assume they held although I can not see them.
Hopefully through feedback from users you can quickly learn and improve even more. Best wishes to much success!
In another post there was a complaint about not being able to push the buttons with thick 5mm gloves on. Many of us dive cold water, and a cold hand/finger may find pushing the buttons very hard, especially with no feeling in said finger.
I find the short USB cable to be a pain, especially since I use a laptop often in my lap. It would be hanging from the front of my desktop if plugged in there to charge. I understand you will probably be offering it with the longer cable to help control the squelch when plugged into a computer. Someone mentioned it is the same connector as some Blackberry's?
We have heard there is a new case being manufactured. I would be curious to see one since I still haven't figured out how I am going to carry it long term. For now it will probably be clipped off into my left pocket, utilizing cave line and a bolt snap tied to the lid. What about offering different options for diver attachment points? Personally I do not think I would trust the metal clip currently on it to keep it attached to my scuba kit being drug into and around my boat (Probably going to remove the metal clip currently installed for cleanliness in my pocket, since it is a suicide type clip). Nor do I want it dangling by clipping the radio off to my BC anywhere. Since I dive a BP/W with a can light, my preference would be to store it directly behind my can light on the 2" waist harness, held in place by the can light which is held in place by a buckle. In other words what about offering possibly a bolt on, or cast in solid mount 2" slot?
Seems like somewhere on this page Nautilus Lifeline Support Registration there should be a link to get the MMSI number from BoatUS with the "how to" write up from another thread found in this forum. Following the instructions was pretty straight up for getting the MMSI number.
The interface software is not laid out properly as you can see in the photo below it is impossible to see what channels are set. Every page has areas where words are cut off too. I set the channels with no issue and assume they held although I can not see them.
Hopefully through feedback from users you can quickly learn and improve even more. Best wishes to much success!