Cost of Servicing Scubapro Regulators

What's the most you have ever paid for an annual regulator service?


  • Total voters
    22
  • Poll closed .

Please register or login

Welcome to ScubaBoard, the world's largest scuba diving community. Registration is not required to read the forums, but we encourage you to join. Joining has its benefits and enables you to participate in the discussions.

Benefits of registering include

  • Ability to post and comment on topics and discussions.
  • A Free photo gallery to share your dive photos with the world.
  • You can make this box go away

Joining is quick and easy. Log in or Register now!

Do they charge more if your regs are Titanium? I just got a set and will be getting them done prolly next year.
 
Do they charge more if your regs are Titanium? I just got a set and will be getting them done prolly next year.

parts should be the same. only increase in cost is if they are the O2 compatible kits. These are a waste of money on titanium reg sets since they can't be used with high concentrations of O2, so if a shop tells you that you need them for "nitrox" tell them to shove off and find a better shop
 
For Apeks, I paid about US$55.00 for one set of 1st stage service kit and two set of 2nd stage service kits locally. A complete overhaul for one set should cost around US$100.00 if done by LDS. And since I have several Apeks sets(rec and tec), the cost is too high to justify it so DIY.
 
No difference in service fee for a Ti regulator. None whatsoever. Anyone who tells you this is scamming you.
 
Unless they are using special tool only design to work on Ti material!!!:)
 
Unless they are using special tool only design to work on Ti material!!!:)

Yeah. But I try and avoid using a left-handed titanium screwdriver on SP regs.
 
$30 per reg labor charge is excessive ONLY if a customer brings in his gear clean and corrosion free and completely ready for just a parts swap. I've been doing this for a long time, and "20 minutes per reg" only happens in the DEMA clinic with loose new regs.
About 80% of the regs I service need a detergent or phosphoric acid-based dip because of the verdigris corrosion (what owner thinks he got good service when he gets his green-flecked reg back that way?), then maybe a few minutes in the ultrasonic, then pressure air drying and hand cleaning the dried excess Christolube from the last shop.
Many pistons get a little hand polish with 6000 grit Micromesh at the knife edge due to sand blasting pockmarks where high pressure air enters from the tank.
Now clean the sand out of the second stage between the barrel and the adjustment knob. Inspect the diaphragm for holes. Don't forget to disassemble the exhaust for the occasional cockroach nibbled exhaust valve.
Torque it all to spec and tune it perfectly. Pressure test it in a big sink to test for any leaks (or too many bubbles on that HP hose that you didn't want to spend $40 to replace last year). Dry it again. Package it up with photos of the problems you fixed to justify those expensive replacement parts (yes, I'll agree with the other posters about the cost of kits), and then fill out the bill.

Twenty minutes? Never.

I'm certified by over a dozen manufacturers and LOVE doing it right! But I only do it for my friends, or when the shop really needs extra help, because you can't survive on what you earn if the shop charges $25 per reg retail.

I started for the same reason most of you did: at $30/reg, I was so disgusted by the quality of the service I got, that I got trained to do it myself. But you can't make money at those rates if you do it perfectly, unless you're doing it at scale, with six guys all working full time in a big shop.

As others have noted, the key is finding that rare good shop. You can argue about the parts cost, but the labor charge is a steal.

My 2 cents.
 

Back
Top Bottom