Uwatec smart pro battery

Please register or login

Welcome to ScubaBoard, the world's largest scuba diving community. Registration is not required to read the forums, but we encourage you to join. Joining has its benefits and enables you to participate in the discussions.

Benefits of registering include

  • Ability to post and comment on topics and discussions.
  • A Free photo gallery to share your dive photos with the world.
  • You can make this box go away

Joining is quick and easy. Log in or Register now!

Okay there in my gallery and now??

That must have failed also since I don't see a gallery with your username on it.

Capture.jpg

If you do see it, find your photo click on it and open it up in a medium view. There will be links off to the side. Highlight the second one down (Linked Image) Hit Ctrl-C and then paste it into your post. Note: you have to Ctrl-C to copy the link - not highlight and right click select it.
 
Last edited:
Hy board.
I folowed the procedured described here for the Rev. D and it worked. Thanks for sharing precious information.
Had some problem with the wrench first time, but if i keep the contact for @ 5 sec... it appears.

2.jpg3.jpg4.jpg
Happy divings
 
Hi DeDragonSlayer,

i'm trying to replace the battery of smart pro rev D, i've soldered the new battery and the wrench symbol appears
is that i need to ground the pin of the IC now in order to reset it? and is that i must lift the pin out of the board in order to ground it?
if my soldering skills is not good enough to lift the pin, can i juz cut the pin and ground it?
Thank you and looking forward to your advice. (really done a nice job here :D)

one last question? there 's no software solution for resetting it so far rite?
 
Hi DeDragonSlayer,

i'm trying to replace the battery of smart pro rev D, i've soldered the new battery and the wrench symbol appears
is that i need to ground the pin of the IC now in order to reset it? and is that i must lift the pin out of the board in order to ground it?
if my soldering skills is not good enough to lift the pin, can i juz cut the pin and ground it?
Thank you and looking forward to your advice. (really done a nice job here :D)
Yes, as I wrote before, the pin is grounded by design in rev.D. So you must effectively unground it, and then temporarily ground it again to reset the microcontroller.
You can do by cutting of course, if your cutting skills are better than my soldering skills. :) However this way you risk more damage, because of the increased force needed. You might break off a trace from the main board, or do some more irreversible damage. A soldering iron with a very sharp tip would be my preferred tool. :)

one last question? there 's no software solution for resetting it so far rite?
Not that I know of, my soft only resets the battery counter, not the whole device.
 
Yes, as I wrote before, the pin is grounded by design in rev.D. So you must effectively unground it, and then temporarily ground it again to reset the microcontroller.
You can do by cutting of course, if your cutting skills are better than my soldering skills. :) However this way you risk more damage, because of the increased force needed. You might break off a trace from the main board, or do some more irreversible damage. A soldering iron with a very sharp tip would be my preferred tool. :)


Not that I know of, my soft only resets the battery counter, not the whole device.


Thank for your reply, DeDragonSlayer
I'll try unsoldering it then :)

---------- Post added October 7th, 2014 at 01:59 AM ----------

Yes, as I wrote before, the pin is grounded by design in rev.D. So you must effectively unground it, and then temporarily ground it again to reset the microcontroller.
You can do by cutting of course, if your cutting skills are better than my soldering skills. :) However this way you risk more damage, because of the increased force needed. You might break off a trace from the main board, or do some more irreversible damage. A soldering iron with a very sharp tip would be my preferred tool. :)


Not that I know of, my soft only resets the battery counter, not the whole device.

May i ask one more question?
I've unsolder the pin and ground it, it beeps but then the wrench is still there, with temperature reading blink n displaying oxygen 21%
is it normal? or i need to do something?

Thanks a lot for any advice
 
Uwatec Smart Pro does that. Temperature will stop blinking tomorrow. I don't remember first hand what happens to the wrench symbol (it's been a while since i messed with my computer), but as I understand post #70 the wrench will disappear also.
 
Uwatec Smart Pro does that. Temperature will stop blinking tomorrow. I don't remember first hand what happens to the wrench symbol (it's been a while since i messed with my computer), but as I understand post #70 the wrench will disappear also.


ic, that releases my doubt :)
thank you very much
 
https://www.shearwater.com/products/teric/

Back
Top Bottom